And finally, I came to the table more so-called first-floor plate tapiaugud a rout. Was used for th

Board, of which I spoke a few post back, has achieved a lot of success at work, and to be honest, it is already near to completion. This work is still needed was unimaginably far. Seemingly is a very simple design, but different solutions as accurately as possible by using a variety of measures are just time-consuming. Started was then that the proper size for both legs were shaved (100x100 blocks) and pealislaua part (50x150 sticks). I kept the top part of the table, perhaps less complicated then. At first glance, a nice idea to make all the angles of 45 degrees to the table section beams, promoting the project gathered so much experience, that the next time I'm thinking probably carefully dishwasher not cleaning well every square off to find out whether you still wise to pursue both keeuliseks. My original vision, however, is that the cut nurgasae under 45 degrees, put the stopper dishwasher not cleaning well in total, and that's a good thing. Since the tools are in school, however, there is little accurate and crafts, assumed that the "Combined planer and thickness of the angle of the saw-maker" is sufficient. In fact, he saw a much more serious thing. Namely, after the get together dishwasher not cleaning well at an angle fitting, it became dishwasher not cleaning well apparent that the angles with each other quite a one-on-one meet not go to, all the more so if the adhesive is placed between the lamella and became more angular and a few millimeters of movement gives the meter onto the corner of a rather large difference. The angles were all pressed together, one by one, for it was made 2 abiklotsi with clamping screw for the inside of the notches, they turn thumbscrew with a table and two side turning once, they retreated to one another. If I could put the original plan of the corner and plenty of glue, some puupunnid, Uncle Ants criticized it immediately brought me down and rellaka by the end of the lamellae suitable for cutting disc and nozzle. Unfortunately dishwasher not cleaning well I do not have pictures of this, but it is the result of the show:
The first three sides of the so-called "U-characters' images together to get was a bigger problem, however, was just sneak in between the fourth and the kind of art that was between the previous method did not want to pull, wanted terribly slanted sides, so I just got the latest between the rubber hammer struck. dishwasher not cleaning well This day, however, was the most productive. Table with sanded as well (especially the corners) and got tackled feet. Specifically, the plan was curved feet from one corner (on top of the table top as well). Because of this ingenious solution for single pole, Planer came on top of a more or less curved by most of the lost ground, and the last little corners rasp of sandpaper and a myriad of finishing touches - every decent result. The camera dishwasher not cleaning well comes with today was not, followed by inferior phone pictures:
Moreover, it was noted, however, been puupunniauke table on the back of the plate, where the legs are attached. The principle consists in the fact that I do not want to use any metal steps lauakonstruktsioonis, so all connections are wooden pins / lamellid / puupunnid and hidden.
There were also quite a simple and effective way. Came foot off the tongue indicate approximate locations into a small liistunael dishwasher not cleaning well the game, so that is 3mm to bite the head off and then pressed into a desk drawer. It also came to their feet, and all the places previously labeled.
And finally, I came to the table more so-called first-floor plate tapiaugud a rout. Was used for this purpose käsifreesi otsfreesiga, väljaulatavusega 15mm. And by using the cross-braces became more or less straight and decent tapiaugus cut out:
Working of the wood parts are still about 1-2 hours max nokitsemist: The lower part of the plate cut to size, put together with the feet on the table to mill the edges and polish here and there. Then, still needs to get the glass to fit that goes on the table, in the center. In his old window project that looks new window corners, metallhingesid, metallhaake, glasses, fine-tuning, I also made some images (but not the last stage, nothing moved forward):
2014 (6) February (2) January (4) 2013 (37) August (2) August (8) June (4) May (9) April (2) March (4) February (3) January (5) 2012 (37) December (5) April (2) March (11) February (13) January (6) Savings Invite, stand, coffee table Coffee table Savings Invite other Coffee Table, Window 3-hobby plaque Puidutöötlemishooaeg 2011 (54) December dishwasher not cleaning well (1) November (7) October (7) September dishwasher not cleaning well (4) August (3) July (1) June (5) May (5 applicable) April (2) March (19)