This seemingly simple machines due to inexperience and lack of the right tools has been a challenge

This seemingly simple machines due to inexperience and lack of the right tools has been a challenge to me and took a lot of time to complete. But I've learned ... Is not that the purpose anyway? To try, to learn, to share what they have learned and how much easier it can be done the same project who will try to give you an idea. I do a lot less than the same machine takes me. Will I use the same material at the end of the question let me explain. I use material: 14x10 cm size 70 cm in length two uprights 10x6 cm in size 55 cm in length medium beam 14x10 cm in size and 55 cm in length underbody 10x6 cm in size 2 mm welded into sheet fixed to 14 mm nut (nut at the bottom sheet 14 mm tip is perforated with) 20x20 cm in size 2 mm to 14 mm nut welded into sheet fixed to the (at the bottom of the nut plates are drilled, closed) 1-meter-long worm Props to remain in the top 10 cm of the beam places I marked the future. I opened the beam in place giriceği planting. To form the lower base of 14x10 cm size and 55 cm in length 10 cm in length on each side of the board and bottom of the 6x6 cm with 4 cm gap flaps to be cut. Sub-floor atrium to the late planting identify the places, locations opened in planting. I have explained above, in three sentences took me a lot of work. Open places, especially on planting has been a challenge to me. Props to pass through the holes in the middle stainless table of the beam 10 cm and bottom end portions of the flap was fixed with a bit of sanding and planting did not facilitate the settlement. Beam and bottom of the strut insert, 15 mm vertical holes opened by the end. I started putting wood glue into the holes, stainless table 15 mm wooden escort (nails / screws used in place of wood) I era. All joints escort board I used 15 mm. The machine frame has been completed. I waited a few hours for the glue to dry. With 15 mm end of the beam, put a hole in the middle. 14 mm bolts that secured 10x6 cm steel plate over the hole so that I screw. 20x20 cm 10x10 cm steel plate bolted to the two boards. From mid-beams spend endless screw until the tip turned out. 20x20 cm print board over the end of the worm, sıkışınca turned up. Well ... ready ... forever machine screw machine greased with oil, I turned the pressure above board ... The first observation is happily walking down ... 1-meter worm stayed a little longer. Fortunately, pressure from the board dismantle the screw, worm cut a little to settle the issue. Olive pulp under pressure while turning stainless table the board of the bag that I have trouble imagining and think what you like. Due to the rotational motion of the square board bags will not be printed in a healthy way, and probably for savrulucak. Print wood, and of course the nut welded to a round plate to solve this problem. Instead of putting the bags in the healthiest stainless table olive paste, 21-22 cm in diameter and 35-45 cm in length and put them into a bucket below the hole and turn to the side surface of the sleeve. 20 cm diameter pressure lowering down comfortably in wooden hive, the hive from the side and below the surface of the water will be olives. Conclusion: Printing board and caused the nut plates should be rounded. Now I'd planned to do so again this machine, iron instead of wood frame profiles think it would be easier to do. A blacksmith in a few hours with the right equipment will be ready. After making changes on the machine attempts stainless table to tight I'll start.
to be bored here grams of olive oil to cover the value of gold and trailers :) harvest is low but the quality will be much higher, I think. heavy oil Do you have information about whether it? would be considerably heavier than a pure income I wonder? stainless table 10:04 pm
Hello Mrs. Nalan; We have now completed stainless table the presses, it's time to olive crushing and squeezing process. From the weekend is progressing slowly due to the work done by the weekend, but I'll catch season. I read many years ago about Olive Artur Unsal what I read in the book In Search of the Eternal Tree'm trying. One of the important factors that determine the acidity of the oil collected is tightened How long after that was written. Stringent than those described in the book I'm planning to do both, first cold-pressed, and the second by adding hot water tight as I'm planning to do. Let's see how the results will be? Last year, I tried my tight olive juice presses had failed. 10:35 AM
Hi Murat, although the work myself if I do not take the time to write my blog I have seen here. New mangle your (PRES's) wish to be beneficial. You will have a humble suggestion. Boiled stainless table nut that screws to the beam (6x10) piece of sheet metal on the bottom of the beam and not out of the beam vidalas you would be if you could have done a lot more accurate. When you do, because I'm tight in the press for all the clamping force applied on the beam steel plate (6x10) and will make a charge up to the screws holding the vid will be forced to disengage. Time